Hello,
I want to make a bot thats scan the market if its still 0-0 (this is already made) and also scan in the first half the odds are below......
It only may take 1 bet not more.
Example barcelona - real madrid.
I want to lay the under 1.5 goal at 0.0 but by 10 min the odds are still above my setting of 3.5 odds it needs to scan everyminutes (seconds) if the odds are below 3.5 if that true and then 0-0. Then place a bet.
I made this so far see files
how to scan market if odds below a certain price and place 1 bet
- Thebest147
- Posts: 93
- Joined: Thu Nov 05, 2015 8:01 am
There should be something in the automation section,
Finding odds on favourites and you can amend it from there to suit your system.
Finding odds on favourites and you can amend it from there to suit your system.
Yes but how? because it also scan the 0-0 but this only on the 15 till 17 min onetime in the bat file. Only i want to scan from 00.00 till 00.45 min also if price is lower then?Thebest147 wrote: ↑Mon Feb 24, 2020 1:06 pmThere should be something in the automation section,
Finding odds on favourites and you can amend it from there to suit your system.
I think i found the solution here on the forum See answer below
Think I might have answered my own question
I'm triggering the place back bet 300 times with 10 sec reload (50 mins) and setting a condition that matched bets are less than 1 .. hopefully that should keep it trying to place the bet and only place it once
The greening on goal is set to condition of matched bets more than 0 so shouldn't trigger until the bet is placed and a goal is scored.
Think I might have answered my own question
I'm triggering the place back bet 300 times with 10 sec reload (50 mins) and setting a condition that matched bets are less than 1 .. hopefully that should keep it trying to place the bet and only place it once
The greening on goal is set to condition of matched bets more than 0 so shouldn't trigger until the bet is placed and a goal is scored.
I see the time from till does the scan?
As Dabbla said you don't need the lay bet rule to trigger 44 times, just once will do if you only want to place a single bet.
I can't see any problems regarding storing the value of 0-0 then using that as part of your lay rule conditions - have you checked your log and automation tab at the bottom of guardian to see whats triggering and when?
However you do have the 'Green on 2 rule' applied to Betfair row 2, this should be row 1 (the same as the selection your laying) otherwise it will never green up
I can't see any problems regarding storing the value of 0-0 then using that as part of your lay rule conditions - have you checked your log and automation tab at the bottom of guardian to see whats triggering and when?
However you do have the 'Green on 2 rule' applied to Betfair row 2, this should be row 1 (the same as the selection your laying) otherwise it will never green up
This thing i saw yesterday so fixed this. Now again i have setup a game. There is placed a lay bet and there is a goal after that nothing happends. Here are the logs and automation files.Dallas wrote: ↑Tue Feb 25, 2020 3:09 pmAs Dabbla said you don't need the lay bet rule to trigger 44 times, just once will do if you only want to place a single bet.
I can't see any problems regarding storing the value of 0-0 then using that as part of your lay rule conditions - have you checked your log and automation tab at the bottom of guardian to see whats triggering and when?
However you do have the 'Green on 2 rule' applied to Betfair row 2, this should be row 1 (the same as the selection your laying) otherwise it will never green up
Automation of scores check Log of scores check Automation of the market
These are the rules
[*]It need to scan if there is 0-0 and the lay price is below 3.00, is this ok place a lay trade.
[*]Then needs to look if there is a goal scored 0-1 1-0 if it is, check if 50% or higher profit, so yes take profit
[*] if its less then 50%go on and scan for 1-1 2-0 0-2 and take the whole profit if there is a second goal.
Next post i will share files again.
I hope someone have the solution, thanks again dallas and dabbla
You do not have the required permissions to view the files attached to this post.
I think i have found the problem only not solution
My trigers are not updated? Anyone know how to fix this?
You do not have the required permissions to view the files attached to this post.
Try this i have nested the stored values for you in the grening rule.
From the manual
Automation
· Conditions can now be wrapped in groups. Groups can be nested if required, every group must have a start and an end. A group is started or ended using the special condition types at the top of the picklist. Each group can be configured to control how the conditions are tested (whether they ALL need to be true or just one of them etc). This effectively adds AND/OR/NAND/NOR logic to Automation Conditions.
As in previous versions, any conditions not contained in a group must all test ‘True’ for the rule to trigger.
The scan file you using clears all signals after goal a shout or suspension, so you don’t need all the signal conditions. All you would need is a( signal is set) for the score line you require.
From the manual
Automation
· Conditions can now be wrapped in groups. Groups can be nested if required, every group must have a start and an end. A group is started or ended using the special condition types at the top of the picklist. Each group can be configured to control how the conditions are tested (whether they ALL need to be true or just one of them etc). This effectively adds AND/OR/NAND/NOR logic to Automation Conditions.
As in previous versions, any conditions not contained in a group must all test ‘True’ for the rule to trigger.
The scan file you using clears all signals after goal a shout or suspension, so you don’t need all the signal conditions. All you would need is a( signal is set) for the score line you require.
You do not have the required permissions to view the files attached to this post.